Supply of Clamp-On Ultrasonic Flow Meter Tender, Assam - 42453399

Procurement Summary

State: Assam

Summary: Supply of Clamp-On Ultrasonic Flow Meter

Deadline: 09 May 2020

Other Information

Notice Type: Tender

TOT Ref.No.: 42453399

Document Ref. No.: SGI4143P20/4

Financier: Self Financed

Purchaser Ownership: -

Document Fees: Refer Document

Tender Value: Refer Document

EMD: ₹ 88000

Purchaser's Detail

Name: Login to see tender_details

Address: Login to see tender_details

Email: Login to see tender_details

Login to see details

Tender Details

Supply of Clamp-On Ultrasonic Flow Meter: 1. Transducer Type: Non-Intrusive (one Pair of Sensors) 2. Mounting: Clamp-On 3. Measuring Principle: Ultrasonic Transit Time 4. Range: Bidirectional -40 to 40ft/s, (-12.2 to 12 .2m /s) 5. Pipe Size (diameter) : 4 in To 20 in (101.6 Mm to 508 Mm) 6. Pipe-Thickness Range : 0.05 in To 0.3 in (1.3 Mm to 7.62 Mm) (in Case of 16 Inch Dia) 7. Accuracy :+/- 1% or Better of Measured Value Over the Entire Flow Range. 8. Repeatability : +/- 0.3% or Better of Measured Value Over the Entire Flow Range 9. Protection Against Emi/rfi, Lightning Strike and Should Be Intrinsically Safe for Use at Hazardous Locations. 10. Weather-Proof Ip-67 or Better. 11. Enclosure Classification/ Housing: Explosion_ Proof - Class-I, Division-I ; Group B, C & D, E Ex D Iib T4. 12. Area Classification: Hazardeous Area - Class I, Division 1, Groups B, C & D. 13. Approvals Required: Peso/atex for The Entire Flow Meter Unit Comprising of The Transducers (2 Pair) and The Electronic Measuring Unit. Documentary Evidence Regarding the Same Must Be Submitted Along with The Bid. 14. Outputs Required: I) Galvanically Isolated Analog Output of 4-20 M a Dc, without The Use of Any External Power Supply, for Full Range of Flow to Drive a Load of 600 Ohm for Interfacing to Scada Ii) One Change Over Contact (normally Open) Output Corresponding to Every Kilolitre of Service Delivery 15. Display of Flow Rate and Totalized Output. 16. Electronic Measuring Equipment Should Be: A) Modular in Design. B) Flameproof Suitable for Use at Hazardous Locations . C) Weather Proof Ip-67 or Better. D) Should Have Built-In Facility for Fault Diagnosis. E) Should Have Front Panel Display of Flow Rates and Total Kilolitres Delivered and % Flow. F) Power Supply for Operation: 10-30 v Dc. 17. the Electronic Measuring Unit Shall Be Mounted at Field Near the Transducers. the Output from The Electronic Unit Shall Be Connected Through Signal Cables to The Rtu at Control Room (approximate Distance to The Control Room: 500 Metres). the Supply of These Signal Cables Is in The Scope of The Bidder. 18. Sensor/ Transducer Cable: The Supply of Cable Between the Sensors and The Signal Converters/ Flow Electronics Is in The Scope of The Bidder. Suitable Mounting Fixtures for Fixing the Sensors on The Process Pipe Shall Be Supplied by The Selected Bidder. Bidder Must Supply Suitable Flameproof Cable Glands, Mounting Fitments and Connectors for Disclaimer: The Due Date Mentioned Is an Assuming Date, Vendor Must Contact Tendering Authority for More Details Cable Termination at The Flow Meter and Flow Electronics End. 19. Supply of Accessories: I) Suitable Ultrasonic Couplant for Boosting the Signal Strength of The Transducers to Be Supplied by The Bidder Along with Each Flow Meter. 20. Service Conditions: I) Service Fluid: Crude Oil, Hsd, Motorised Spirit(petrol) and Kerosene Oil Ii) Flow Type: Uni-Directional Laminar Flow Iii) Flow Range: 50 to 500 Kl/hr Iv) Service Area: Outdoor; Hazardous V) Relative Humidity: 95% Vi) Operating Ambient Temperature: 4-Degree C to 60-Degree C Notes to The Bidders: I) Operation & Maintenance Manual and Software for Pc Connectivity, if Any Shall Be Provided by The Selected Bidder. Ii) Warranty: Bidder Shall Provide a Minimum Warranty Period of Twelve Months from The Date of Commissioning or Eighteen Months from The Date of Supply Whichever Is Earlier. Iii) Price Break-Up of Every Item/accessories, Mentioned in The Quotation Shall Be Provided.

Documents

 Tender Notice