|
1 |
Supply only channel speaker system Three way Tri - Amplified Cinema Screen Array with following Accessories |
a - Complete set comprising low-frequency enclosure and mid by High-frequency encl low profile, flat front waveguide design for baffle-wall installation, depth not exceeding 450 mm b - Low-frequency section 2 x 15 Inches 380mm drives, vented gap cooled-power handling not less than 1200 W,AES 2 hour, 4 ohms nominal c- Mid-frequency section 2 x 8 Inches 200 mm differential-drive drivers, power handling not less than 700 W, 4 ohms nominal d - High-frequency section compression drive with 4 Inches,100 mm voice coil, 1.5 Inches, 38 mm exit, power handling not less than 150 W, 8 ohms nominal e- Frequency range -10 dB 30 Hz - 20 kHz, frequency response +- 3 dB, 40 Hz - 19 kHz f - Maximum SPL not less than 128 dB continuous by 134 dB peak at 1 m. g - Coverage - 90 degree horizontal 20 Degree up by 30 Degree down vertical. Crossover frequencies approx. 250 Hz and 1.3 kHz. Screen-spreading compensation. |
3 |
Sets |
120 |
|
2 |
Supply only Subwoofer system - Dual 18 Inches Bass - Reflex Cinema subwoofer with following Accessories |
a - Two 18 Inches 460 mm Vented-gap cooled low frequency drivers in a braced bass-reflex enclosure 19 mm particle board, 25 mm baffle and back panel, enclosure tuned at approx 25 Hz. <br>b - Power handling not less than 950 W ,AES 100 Hour and 1200 W AES 2 hour, rated impedance 4 ohms minimum 3.2 ohms <br>c- Usable response down to 22 Hz -10 dB without EQ -3 dB at 35 Hz or lower. <br>d - Sensitivity not less than 100 dB 1W 1M 40-100 Hz, maximum continuous SPL not less than 131 dB by peak 137 dB at 1 m single unit. <br>e - Recommended crossover - high pass 20 Hz, low pass 80 - 150 Hz. Colour coded push terminal inputs. |
2 |
Nos |
120 |
|
3 |
Supply only Power - Amplifier supply only 4 Channel Cinema Amplifier with Built-in DSP with following Accessories |
a - Four Channel amplifier with bridgeable outputs standard 19 Inches 482 mm, 2 U rack mount chassis. b - Rated Power 1 kHz, 0.5 percent THD not less than 700 W x 4 at 8 ohms, stable load down to 2 ohms. c - Built in 96 kHz by 32-bit floating point DSP - crossover parametric EQ FIR filtering delay up to 1000 ms and limiting no separate speaker processor required. d - Built-in speaker tuning presets for cinema loudspeakers. e - Frequency response + 0.5 dB ,20 Hz - 20 kHz THD not more than 0.35 percent, damping factor 1000, signal to noise ratio 105 dB, A-weighted. f - Front panel LCD with controls for configuration and channel mute, network TCP by IP, SNMP remote monitoring GPIO port for preset recall, mute and power on by off. g - Power Supply 100-220 V +- 10 percent, 50 by 60 Hz Maximum fan Noise 51 dBA barrier terminal speaker outputs accepting up to 10 AWG wire. |
4 |
Nos |
120 |
|
4 |
Supply only Surround Speaker - Compact Two Way Cinema Surround Speaker with following Accessories |
a - Two-way design 8 Inches, 200mm long-throw low frequency driver and 1 Inches , 25 mm soft dome high-frequency driver with constant-coverage horn. b - Power handling not less than 150 W, AES-2 Hour and 70 W, AES - 100 Hour, 8 ohms nominal c - Frequency range -10 dB, 50 Hz - 20 kHz, response +-3 dB, 65 Hz - 18 kHz, crossover approx 3 kHz. d - Sensitivity not less than 91 dB free field ,1 W, 1 m, maximum SPL not less than 116 dB continuous by 122 dB peak at 1m. e - Coverage approx 100 degree horizontal x 90 vertical, surround high-frequency contour ISO 2969 Curve X. f - Lightweight moulded black enclosure with 20 Degree downward angled baffle, black grille, binding post inputs on top of cabinet weight not more than 5 kg. |
20 |
Nos |
120 |
|
5 |
Supply only Surround Speaker mounting Brackets with following accessories, Heavy duty wall-mount brackets with tilt by swivel adjustment, suitable for the offered surround speaker. |
Supply only Surround Speaker mounting Brackets with following accessories, Heavy duty wall-mount brackets with tilt by swivel adjustment, suitable for the offered surround speaker. |
20 |
Nos |
120 |
|
6 |
Supply only Cinema audio processor along with following Accessories |
a - Cinema audio processor supporting 7.1 and 5.1 Surround formats, with expansion slot for field upgrade to immersive object-based audio. b - Output - 16 channels analog, or 16 Channel digital supporting AES67 or Blu-Link protocols. c - Internal loudspeaker crossover and high-resolution multi-rate equalisation. d - Built in booth monitor colour touchscreen front-panel interface, web user interface for remote configuration and control. e - Modular mechanical design for field upgradability and serviceability, integrates with multichannel cinema amplifiers, supports setup and system-calibration software. |
1 |
Nos |
120 |
|
7 |
Testing by Sound Engineer and Calibration Charges with following accessories |
Calibration and alignment of processor, amplifiers and speakers EQ, delay, Levels by a qualified sound engineer, including to and fro charges. |
1 |
Job |
120 |
|
8 |
Fixing by Installation of speaker brackets and cabling by a qualified electrician including to-fro charges for srl item no 1 to 7. |
Fixing by Installation of speaker brackets and cabling by a qualified electrician including to-fro charges for srl item no 1 to 7 |
1 |
Job |
120 |