Expired Tender Germany ICB TOT Ref. 35012081

Contract notice: Loadbearing equipment Tender in Germany - 35012081

Tender notice from Germany, published on 26 Jul 2019.

Executive Summary

The PHYSIKALISCH-TECHNISCHE BUNDESANSTALT has issued a Tender notice for the procurement of a Contract notice: Loadbearing equipment in the Germany. This Tender notice was published on 26 Jul 2019 and is scheduled to close on 29 Aug 2019, with an estimated Tender value of Refer Document. Interested bidders can access detailed Tender information, eligibility criteria, and complete bidding documents by referencing TOT Ref No. 35012081, while the tender notice number is 351409-2019 and Register on the platform.

Key facts

Summary
Contract notice: Loadbearing equipment
TOT Ref. No.
35012081
Document Ref. No.
351409-2019
Country
Germany
Notice type
Tender
Competition
ICB
Publication date
26 Jul 2019
Bid deadline
29 Aug 2019
EMD
Refer Document
Tender value
Refer Document
Purchaser ownership
-
Financier
Self Financed

CPV classification

Purchaser details

Purchaser contact is for registered users

Login to see details

Tender details

Object of the contract
Loadbearing equipment
Description: Contract notice: Loadbearing equipment
Authority Type: Ministry or any other national or federal authority
Contact Nature: Supplies
Procedure: Open procedure
Document: Contract notice
Regulation: European Union, with participation by GPA countries
Award criteria: The most economic tender
CPV code: 34950000, 34950000
CPV Description: Loadbearing equipment.
Delivery of levers and cast components
Reference Number: Z.1131D-Z379072401
At PTB, a WIND competence center will be set up to support the wind industry. Part of this competence center will be a torque standard measuring device for high torques. This measuring device is an in-house PTB development and is being used by contractors in several stages
Main site: Euler construction on the grounds of the Physikalisch-Technische Bundesanstalt in Braunschweig.
Delivery of levers and cast components
The measuring system is used to calibrate torques up to 5 MN.m. In addition to the torque, bending moments up to 1 MN.m and axial forces up to 400 kN can be applied. About it is a dynamic superposition of a turning or bending momentwith a maximum amplitude of 100 kN.m and a maximum frequency of 3 Hz. The required hydraulic cylinders are used for load generation for high-torque calibration. The lever has a length of 3 m (based on the torque). Two cylinders, each with a nominal force of 1 200 kN, are needed to generate the torque. For the producersA total of 4 cylinders each with a nominal force of 100 kN are provided for the bending moments. For the secondary cylinders for aligning each 100 kN nominal force are provided. The machine is divided into an actuator side for generating the forces and moments and a measuring side for measuring the calibration quantities. Servo cylinders are used to generate the forces and moments. Theseare supported on the actuator frame and are coupled to the actuator lever. The lever ends are used for the coupling. The lever ends are intended only for the actuator lever, the measuring lever is cast from one piece. The actuator frame is movable and is hydraulically clamped by clamps on a shaft during operation. The bearing of the shafts take over the Aktorrahmen-Gegenlager. The cross member of the spare load device is also located on the actuator side and serves as a support for the actuator lever when it is in the rest position. The actuator lever, the actuator lever ends and the actuator frame counter bearings are part of the tender (modules I and II). The crossbeam of the spare load device should be offered as an option (module III).
Between AkTor- and measuring lever is mounted the Pruefling. Thus, the tester passes on all moments and forces from the actuator to the measuring side and can measure them. Two adapter parts, which are also part of the tendering process, are required for mounting a PTB reference torque transducer. However, these should only be offered as an option (module III)gte moment over the measuring lever again disassembled into a Kraeftepaar. The forces are measured individually by calibrated force transducers. In addition, parasitic forces and moments are measured by suitably prepared bending joints. The component consisting of force transducer and strain gauge-applied double bending joint is also referred to as a measuring strand in the further course. For the calibrationg the force signals of the measuring lines are evaluated and compared with those of the test piece. The measuring streets are clamped in so-called counter bearings (torque cylinders in the DM counter bearings, bending moment cylinders in the BM counter bearings). The measuring lever and the counter bearings are part of this tender (modules I and II).
S. Tender documents
Internet address (URL): http://www.ptb.de

Documents

Tender Notice
Login to view

Similar tenders

Tender Country TOT Ref. No. Bid deadline
Delivery of Two Emergency Fire Fighting Vehicle 20 (Hlf20) Germany 152654068 21 Dec 2026
Roll-Off Container for Extinguishing Water (1X Mtk, 1X Fw Hochheim) Germany 152653835 17 Dec 2026
Fw Lauenau/Rodenberg - Delivery 1X Elw1 Germany 152653652 18 Dec 2026
Sm Kt Truck Roll-Off Tipper 2027 Germany 152653636 13 Jan 2027
Bad Herrenalb - Dlak 23/12 - 2026 Germany 152653469 17 Dec 2026

Germany Public Procurement Intelligence

Frequently asked questions

The bid deadline for Contract notice: Loadbearing equipment was 29 Aug 2019. Bidding is closed.

This tender has been issued by PHYSIKALISCH-TECHNISCHE BUNDESANSTALT in Germany.

The tender value is not disclosed; please refer to the tender document. EMD / bid security details are provided in the tender document.

This tender is Self Financed

The tender is classified under the following CPV code(s): 34950000 - Loadbearing equipment.

The tender notice and related documents are listed in the Documents section above. Select a document to view or download it. Please log in or register to access the documents. If you cannot find additional documents in the Documents section, please log in to your account and Send Document Request from your account section.

The TendersOnTime reference is 35012081. The purchaser document reference is 351409-2019.

See the Similar Tenders section on this page or browse other tenders from Germany.

This tender falls under Materials and Products in Germany. Suppliers in these sectors can track similar Germany tenders using CPV-based alerts.