Acquisition of Pedagogical / Scientific Equipment (Technical Equipment, Laboratory... Tender

Procurement Summary

Country : Cote d'Ivoire

Summary : Acquisition of Pedagogical / Scientific Equipment (Technical Equipment, Laboratory Equipment, Office Supplies, Technical Supplies, Furniture, Computer Equipment, Software, Office Equipment)

Deadline : 26 Jul 2018

Other Information

Notice Type : Tender

TOT Ref.No.: 25117140

Document Ref. No. : F 86/2018

Competition : ICB

Financier : Agence Francaise De Development (AFD)

Purchaser Ownership : -

Tender Value : Refer Document

Purchaser's Detail

Purchaser : UNITÉ DE COORDINATION DE PROJET C2D EDUCATION FORMATION
Sylvain Aliha 2 Plateaux quartier polyclinique rue K20 lot 1338 Ilot 08 Abidjan 01 BP 2141 Tel: + 225 47 84 13 22
Cote d'Ivoire

Tender Details

Tenders are invited for Acquisition of Pedagogical / Scientific Equipment (Technical Equipment, Laboratory Equipment, Office Supplies, Technical Supplies, Furniture, Computer Equipment, Software, Office Equipment) for the Profit of ESA / INP-HB.

ARTICLE 1: PURPOSE OF THIS ADDITIVE

The purpose of this addendum No. 2 to International Bidding Documents No. F 86/2018 is:
1- to make amendments to the EQGs of lot3 and lot5;
2- to make the subsequent modifications to the "list of supplies and delivery schedule" as well as the table of "summary of technical specifications" of lots 3 and 5;
3- to specify the technical specifications of Article No. 17 of Sub Lot 2.1 (see Lot 2);
4- to postpone the date of deposit and opening of the folds.

ARTICLE 2: CHANGES TO THE DQE OF LOT 3 AND LOT 5

The equipment referred to as 'Fibertec ™ 8000 with different levels of automation', (1st article of sub-lot 3.1 (see lot 3), is transferred to sub-batch 5.5 (see .. lot 5)

Therefore, DQE lots and sub - aforementioned items are amended as follows:

lot 3: Acquisition of equipment for agricultural lab
Article Number DESIGNATION TECHNICAL SPECIFICATIONS LOW

sub lot 3.1: Acquisition of equipment for agricultural lab
1
Backpack Sprayer • 4-Gallon Island
• Multi nozzles

2
Sprayer • Model A3S
• Two CO2 bottles
• Header: 3 liters
3 Nozzles and accessories • For herbicide application
4 Vertical mixer mill D type BMV 5 or equivalent Feed silo:
• Type: SG4
• Capacity: 2600 liters
Equipment:
• Electronic level detector with time delay
• Regulator suction flow rate
• Magnetic protection
Crusher:
• Power: 15 kW
Equipment:
• 2 circular perforated grids Ø4-6mm
• 8 reversible mobile hammers on 4 sides
• Rotational speed: 3000 rpm
• Pipes: galvanized steel
• Suction Ø100 mm
• Ø100 or 150 mm discharge

• Box comprising: - Manual delta starter
• Ammeter for absorbed intensity control
• Thermal protection switch
Vertical mixer:
• Type: MV5
• Power: 5.5 kW
• Capacity: 4000 liters
Equipment:
• 2 decompression air socks
• 1 emptying outlet: with bagging valve for bagging
• Contactor and thermal protection
• Option: air expansion box with 2 sleeves
5 Manual precision seeder • Steel main material
• Hopper
• Distribution cavities
• Regular distribution of seeds every 4 cm
• A handle pulling the seed drill
• 3 possible seed sizes
• Brush adjustment.
6 Agricultural tractor Engine:
• 4 cylinders
• 130
HP, with air-conditioned cabin • Minimum power of 126 hp according to 97/68 / CE
• Displacement of 4530 cm³

Transmission:
• PowrQuad Plus box - 16/16, 38 km / h
• Includes a electric left-hand reversing switch.
• 3rd point with ball joint - category 2

REAR AND FRONT REAR
HITCH HITCHES
• Lift arms with hook - Category 2

STABILIZER
• Stabilizers adjustable on both sides
• Left and right sides

REAR POWER TAKE-OFF (PDF)
• Independent rear 540 / 540E / 1000 rpm and with selector

LOT 5: Acquisition of technical supplies
Article number DESIGNATION MINIMUM TECHNICAL SPECIFICATIONS Subpack

5.5: Farming equipment
1 Fibertec ™ 8000 with different levels of automation • Level of automation: fully automated
• Positions: 6
• Capacity / day: 36
• Sample holder: glass crucible
• Sample size: 0.5 - 3g
• Measuring range: 0.1% - 100%
• Capacity per batch: up to 6 samples
• Capacity per day: Up to 36 analyzes (raw fiber method)
• Repeatability: ± 1% compared to 5% - 30% of the fiber content
• Power supply: 200 - 240 V 50 - 60 Hz
• Power consumption: 2000 W
• Water supply: minimum tap water 2 l / min (4-25 ° C, depending on the water pressure)
• Weight Load: 67 kg
• Dimensions (W x D x H): 730 × 390 × 640 mm
NB: Supply, installation, start-up and in-service training
2 sintered glass filter n ° 1 for fibertec 8000 • Capacity: 50 ml
• Porosity: 100 - 160 ?m

3 Sinter filter crucibles N ° 2 in glass for fibertec 8000 • Capacity: 50 ml
• Porosity: 40 - 100 ?m
4 Bins for planting weeds and crops (1020 Trays)
• traditional sized thermoformed tray
• allows watering of pots, consisting of bottom &
middle point drainage holes • dimensions (Longxlargxhauteur): 54.3cmx28cmx6.2cm
• reusable
• used to create compact, efficient growing systems for Bedding Plants

ARTICLE 3: CHANGES TO "LIST OF SUPPLIES AND CALENDAR "AND" TABLE OF SUMMARY OF TECHNICAL SPECIFICATIONS "OF LOTS 3 AND 5

As a result of the aforementioned changes, the table entitled "LIST OF SUPPLIES AND DELIVERY SCHEDULE" as well as that of the "TECHNICAL SPECIFICATIONS SUMMARY" are modified accordingly, by deleting the item "Fibertec ™ 8000 with different levels of automation". "Sub - lot 3.1 of each of these tables and its inclusion in sub - lot 5.5 of the same tables.

ARTICLE 4: SPECIFICATIONS OF THE TECHNICAL SPECIFICATIONS OF ARTICLE 17 OF SUB-CLAUSE 2.1

The technical specifications of the "pre-defined pressure + data acquisition infiltrometer + pressure sensors" (see article 17 Sub-lot 2 .), are specified as follows:

Sub-lot 2.1: Anatomical models and small equipment for various practical work


Specified technical specifications
(cancel and replace the previous ones)

1 / lnfiltrometer
Features:
- Diameter of the membrane Nylon: 20 cm.
- Internal diameter of the water tank: 5.1 cm.
- Length of the water tank: 81 cm.
- Air inlet pressure of the membrane: 30cm H2O.
- Material of constitution: polycarbonate and plexiglass

Important advantages:
- Disc of infiltration separated for a better stability
- Low volume of water necessary
- Tension adjustable by the user
- Manual reading of the flow of infiltration on the column of water and
Automatic recording

2 / Central acquisition
Features:
- acquisition, storage, in-situ processing capability, post-processing of data, real-time data analysis capability
- collect and store data, and control devices as the brain of the entire business installation

- the data are visualized on site with a laptop (to be added optionally but at the discretion and free choice of the bidder), iOS or Android -
possesses a PC connection via USB
- output data (simple ASCII format for import and use by software such as ARGUS or spreadsheets)
- allows the initiation of measurement operations and programming of control functions as a function of time and events
2.5 to 12V DC supplied to the pressure sensor by the datalogger which can then record the output signal of the pressure sensor (in mV)
- accuracy of at least 0.1mV
- transducer connected to the datalogger, differential pressure: 1 psi (66 mbar)
- capable if possible of controlling external devices such as pumps, motors, alarms, valves, etc.
- internally has a battery clock -
PC support software, keyboard / display to program
- operates independently of AC power, computers and
human interaction
- flexible power input from solar panel, DC power supply, 12V battery
or USB
- On-site battery charging (solar power converter
or AC-DC) with its
own power regulator

- remote monitoring
- makes automated decision-making on site or remotely
for control

- can support multiple telecommunication devices Interface with on-site
and telecommunication devices such as cellular and voice synthesizers,
modems, radio transceivers, satellite transmitters, serial RS232) and ethernet interfaces

- makes data available over varied networks and can provide them using the preferred protocol
- have various options for finding / collecting data directly, remotely
or wirelessly.
- operating temperature range of -25 ° to 50 ° C -
at least 4Mb memory
- additional storage capacity (Compact Flash Module)

- delivered with a 12V battery


ARTICLE 5: CHANGES TO THE DATE OF SUBMISSION OF OFFERS AND OPENING PLIERS
The deadline for submission of bids, initially set for Thursday, June 28, 2018 at 10:00 am Universal Time, is postponed to Thursday, July 26, 2018 at 10:00 am Universal Time.
The place of submission of tenders, namely the "Procurement Service" of the Coordination Unit of the C2D Education-Training Project located in Abidjan, II Plateaux, Polyclinic district, not far from the "SERVIR" Foundation, rue K20, lot 1349, block 139, remains unchanged.
As a result of this postponement, the opening of the bids will take place on Thursday, July 26, 2018 at 10:30 GMT, in the presence of the representatives of the candidates wishing to attend, at the meeting room of the Coordination Unit of the C2D Project. Training whose address is mentioned above.

ARTICLE 6: FINAL PROVISIONS

This Addendum No. 2 completes the Tender Documents of which it forms an integral part. All other clauses of the Bidding Documents not modified by this Addendum No. 2 remain unchanged and remain applicable.

Coordinator of the C2D EF
Bacary KAMARA Project Coordination Unit

[Disclaimer: The above text is machine translated. For accurate information kindly refer the original document.]

Documents

 Tender Notice