Tender notice from Slovakia, published on 17 May 2014.
Executive Summary
The Centrum vycviku Lešt has issued a Tender notice for the procurement of a Tents in the Slovakia. This Tender notice was published on 17 May 2014 and is scheduled to close on 16 May 2015, with an estimated Tender value of Refer Document.
Interested bidders can access detailed Tender information, eligibility criteria, and complete bidding documents by referencing TOT Ref No. 838480, while the tender notice number is 164212-2014 and Register on the platform.
Object of the contract This is a marquee with truss and high-capacity multi-function inflatable halls, or multifunction hall with a large capacity truss intended for prolonged use in extreme climatic variability podmienkach.Svojou must allow: - accommodation in small units fulfilling special tasks - accommodation of large groups - Establish and other specialized workplaces, storage, garaging and repair, rooms for consumption of food, personal hygiene, and implementation of cleansing, treatment rooms and rooms for officers and supervisory službu.Každý piece is equipped with its own heating, air conditioning and lighting, insulating lining, entrance canopy, sun aperture and electrical distribution systems. Other interior trim is intended to present použitiu.Polné tents and large-capacity halls must allow its modular design connecting the various tents and halls to give a unified whole. Must allow for the attachment of ballistic protection to protect the internal space of the tent or shed. Ballistic protection must comply with firearms in categories A, B, C, D energy shot up to 900 J. "mobile workstation for research prevention and rescue of persons and property" shall consist of the prescribed reports and related material in the range: - Accommodation for indoors about 40 people. - Pieces: 6.Zloženie one set / total number of pieces in 6 sets: - Indoors Inflatable structure 1 pcs / 6 pcs - Insulation insert tent 1 pcs / 6 pcs - Home Lighting 2 msg. / 12 spr., - Partition in hall 3 ks/18 pieces - Input shed 1 pcs / 6 pcs - 30 kW heating unit 2 correct. / 12 spr., - GEA 2 Msg. / 12 spr., - Polná bunk bed with box 20 pcs / 120 pcs - Countervailing tiles under the tent 160 pcs / 960 pcs - Transport packaging for tiles 2 pcs / 12 pcs - electric compressor 1 pcs / 6 pcs - Divorce Central reinflation 1 Msg. / 6 Msg. - Accommodation tent for about 20 people. - Pieces: 6.Zloženie one set / total number of pieces in 6 sets: - Stan a rigid piece 1/6 pcs - Insulation insert tent 1 pcs / 6 pcs - Home Lighting 2 msg. / 6 Msg., - Input shed 1 pcs / 6 pcs - Heating unit 1 Msg. / 6 Msg., - GEA 1 Msg. / 6 Msg., - Field lounger 20 pcs / 120 pcs - Polný night-stool 20 pcs / 120 pcs - Countervailing tiles under the tent 80 pcs / 480 pcs - Transport packaging for tiles 1 pcs / 6 pcs - 1 Sunshade pcs / 6 pcs. - Office tent. - Pieces: 3.Zloženie one set / total number of units in 3 sets: - Tent with rigid 1 piece / 3 pcs - Insulation insert tent 1 pcs / 3 pcs - Lighting Home spr 2. / 6 Msg., - Input shed 1 pcs / 3 pcs - Heating unit 1 Msg. / 3 correct., - GEA 1 Msg. / 3 correct., - Table Polný 10 pcs / 30 pcs, - field chair 10 pcs / 30 pcs - Countervailing tiles under the tent 50 pcs / 150 pcs - Transport packaging for tiles 1 piece / 3 pcs - Sun visor 1 piece / 3 pcs - Antistatic flooring 1 pcs / 3 pcs. - briefing and lounge. - Pieces: 1.Zloženie one kit: - Indoors Inflatable structure 1 pc - ECO insulating liner 1 pc - 1 indoor lighting correct. - Input shed 1 pc - heating unit 2 Msg., - GEA 2 Msg., - Non-slip floor covering 1 pc - electric compressor 1 Msg., - Divorce central reinflation 1 Msg., - Table Polný 32 pcs - Polná bench 64 pieces - Countervailing tiles under the tent 160 pieces - Transport packaging for tiles 2 pcs. - Dining room. - Pieces: 1.Zloženie one kit: - Indoors Inflatable structure 1 pc - ECO insulating liner 1 pc - interior lighting 1 Msg., - Input shed 1 pc - heating unit 2 Msg., - GEA 2 Msg., - Non-slip floor covering 1 pc - electric compressor 1 Msg., - Divorce central reinflation 1 Msg., - Table Polný of 24, - field bench 48 pc - Countervailing tiles under the tent 160 pieces - Transport packaging for tiles 2-piece The delivery counter 1 pcs. - Opinion supervisor. - Pieces: 1.Zloženie one kit: - Stan solid construction 1 pc - Insulation insert tent 1 pc - 1 indoor lighting correct., - Input shed 1 pc - Heating unit 1 Msg., - GEA 1 Msg., - Polný Table 2 pieces, - field 4 pieces chair, - Countervailing tiles under the tent 30 pcs - Transport packaging for tiles 1 p. - Infirmary. - Pieces: 1.Zloženie one kit: - Tent with rigid 1 piece - Insulation insert tent 1 piece - Partition 1 piece - Home Lighting 1 Msg., - Input shed 1 pc - Interconnection unit 1 pc, - Heating unit 1 Msg., - GEA 1 Msg., - Polný Table 2 pieces - Fact chair 2 pcs - Countervailing tiles under tent 30 pcs - Transport packaging for tiles 1 p. - Personal Hygiene. - Pieces: 2.Zloženie one set / total pieces in 2 sets: - Stan a rigid piece 1/2 pieces - 1 interior lighting correct. / 2 spr., - WC cabin 24 pcs / 48 pcs - Basin 1 piece / 2 pcs - Countervailing tiles under the tent 30 pcs / 60 pcs - Transport packaging for tiles 1 piece / 2 pcs - Heating unit 1 unit / 2 pcs - chemical toilet 24 pcs / 48 pcs. - hygiene measures. - Pieces: 3.Zloženie one set / total number of units in 3 sets: - Tent with rigid 1 piece / 3 pcs - Shower cabins 6 pcs / 18 units - Home Lighting 2 spr / spr 6., - Heating unit 1 pcs / 3 pcs - sewage pump 3 pcs / pcs 9 - Basin 2 pcs / 6 pcs - Countervailing tiles under the tent 80 pcs / 240 pc - Transport packaging for tiles 1 piece / 3 pcs - Mobile hot water bottle 1 pcs / 3 pcs - Water distribution in a tent 1 SPR / 3 spr.Stan solid construction: - equipment marquee: tent, lined with insulating liner, sun visor, leveling tiles under the tent interior lighting with divorce, heating, air conditioning, packaging for the transport of tent, tension wire, tent pegs, tent pegs bag, hammer, set of spare parts for the repair of simple mechanical parts kit for carrying out at least 20 repairs to damaged parts of the tent in the range of one damage to 0.02 meters, interior fittings according použitia.Hala inflatable structure: - hall equipment: inflatable arena, insulating liner, sun visor, leveling tiles under the tent interior lighting with divorce, heating, air conditioning, compressor 230 V/50 Hz, packaging for the transport of the hall, Strut Bars, tension wire, tent pegs, tent pegs bag, hammer, set of spare parts for the repair of simple mechanical parts, hand pump kit for carrying out repairs to a minimum of 20 damaged parts of the tent in the range of one damage to 0.02 meters, according použitia.Požiadavky internal equipment to verify the quality: - Stan solid construction. - The use of climatic conditions. - External temperature from 40 C to 55 C in zones A1- C1 STANAG 2895MMS. - Dimensions: - Outer length from 3, 000 to 9, 000 mm - external width 6000 mm with a tolerance of plus / minus 200 mm - internal height must the whole length of the tent amount to 1 800 mm, height central part of at least 2 500 mm, maximum 3300 mm - internal floor area must achieve a minimum of 18 meters up to 56 meters - the total weight of the tent in a shipping container without additional floors and other accessories can achieve a maximum of 250 kg. - speed position 8 minutes by trained personnel. Maximum number of persons 4.Požiadavka tent material: - tent material (top of tarpaulins and fabric covering, flooring, tubes or supporting structure) must not be toxic to the skin, releasing toxic fumes and odors, and must be accompanied by judgments about the hygiene, or a certified copy qualified entity authorized testing. - The material must be smooth for easy cleaning with minimal permeability and water vapor clotting. - Tensile top cover sheet and floor must be at least 2 500 N / 5 cm (according to EN ISO 1421). - Tensile next visit? Tear the top of the cover sheet and the floor must be at least 250 N (according to EN ISO 4674-1). - Resistance to abrasion to the first infringement threads, at least 10, 000 revolutions with no visible changes (according to EN ISO 5470). - Resistance to water penetration at least 200 cm (according to EN 1734: 1998). - Resistance to UV radiation. - Resistance to fungi and molds. - Resistance to bending without causing microcracks at 40 C.. - Fire resistance - oxygen index min. 25, combustion gases are non-toxic and non-combustible odkvápajúce part (according to EN ISO 6940). Requirement for internal insulation liner: - Must not be toxic to the skin, releasing toxic fumes and odors -''s assessment must be accompanied by a sanitary certificate, or a certified copy of the qualified entity authorized testing. - Tensile strength must be at least 650 N / 5 cm (according to EN ISO 1421). - Resistance to fungi and molds. - Fire resistance - oxygen index min. 25, combustion gases are non-toxic and non-combustible odkvápajúce part (according to EN ISO 6940). Requirement for resistance to external influences: - Resistance to external temperatures ranging from 40 C to 55 C without shape or design changes in external or internal parts - Resistance external relative humidity up to 99% at 50 C - Resistance to wind speed of 100 km / h, gusting up to 135 km / h., - Resistance to precipitation as rain intensity of 3 mm / min, at an angle of 30 degrees in all directions - Resistance to precipitation in the form of snow, with a limit of snow load of 50 kg/m2 for 24 hodín.Požiadavka to the design of the tent: - Colours outer shell tent in the shade NATO khaki color-fast green (RAL 6031) - Stan not be equipped with any internal supports, including means for mounting lights, - supporting structure must not significantly interfere in the internal space of the tent (up to 400 mm) - External anchors from outside the tent must defend statutes linking with front and side walls - Autonomy of the individual part of the structure individually removable - Possibility of mutual interconnection of individual parts of stanu.Podlaha: - gas-tight connection of the tent into a single unit bearing capacity of the floor must meet the standards without special requirements and 5, 000 N / m² flat, 1, 000 N / m² points. Must be washable and dezinfikovatelná.Vyrovnávacie tiles under the tent: - protecting the tent floor from mechanical damage. Firming and countervailing terén.Okná: - dimensions of 450 x 600 mm, mounted on the side walls at a minimum of 4 units on one side. Format of transparencies, provided moskytierkou and allowing external covering material consistent with tarpaulin stanu.Dvere: - entrance door in the front and side walls according to the design of minimum dimensions width 1300 mm, height 1800 mm.Požiadavky Technology equipment: - Electrical Distribution 230 V/50 Hz power for lighting and sockets, fuse, surge protection, protection against dangerous contact napätím.Osvetlenie and wiring - sub-distribution panel lights with wiring, brackets lamps, wiring from the outlet (at least 12 evenly spaced outlets on both sides), protected by a minimum 16 amp circuit breaker, IP 67.Podružný switchboards equipped with signal lights voltage in all phases of fusing pipe branch for zásuvky.Na seen spot located wiring zapojenia.Vykurovanie: - oil, able to ensure the temperature inside the tent +20 C to + 24 C at a height of 1 meter above the ground when outside temperatures according to the point of use in climatic areas. Mains power supply: 230 V/50 Hz.Klimatizácia: - able to ensure the temperature inside the tent +20 C to +25 C at 1 m above the ground when outside temperatures according to point of use in climate oblastiach.Požiadavky maintenance: - insulating liner Laundry . Other sections provide for the maintenance of pressurized water. If necessary, the possibility of carrying out decontamination. Possibility of carrying out routine maintenance users by technological processes to be specified in the Operations dokumentácii.Požiadavky supplier of the package: - tents and individual components delivered in protective packaging preventing mechanical and climatic damage, allowing decontamination. Palletised in a waterproof container that will extend over more than palety.Hala inflatable structure: - use in climate podmienkach.Prevádzky ability in zones A1-C1 STANAG 2895MMS.Základné Dimensions: - Outer length from 12, 000 to 13, 000 mm, - external width 8000 to 9000 millimeters, - internal height must reach in the central part of at least 4100 mm - internal floor area must achieve a minimum of 90 meters. overall weight of the tent in the overpack without additional floors and other accessories can reach up to 570 kg . speed position within 20 minutes by trained personnel. Number of people 4.Požiadavka me up tent material - material tent (top of tarpaulins and fabric covering, flooring, tubes or supporting structure) must not be toxic to the skin, releasing toxic fumes and odors, and must be accompanied by judgments about the hygiene, or a certified copy qualified entity authorized skúšobnou.Materiál must be smooth for easy cleaning with minimal water absorbency and clotting pár.Pevnost strength top cover sheet and floor must be at least 3000 N / 5 cm (EN ISO 1421). Tear strength top cover sheet and the floor must be at least 300 N (EN ISO 4674-1). abrasion resistance to the first infringement threads, at least 10, 000 revolutions with no visible changes (EN ISO 5470). Resistance to water penetration at least 200 cm (EN 1734:1998). resistance to UV radiation. Resistance to fungi and plesniam.Odolnost to bending without causing microcracks at-40C (EN 1876). Resistance to fire - oxygen index min. 25, combustion gases are non-toxic and non-combustible part odkvápajúce (EN ISO 6940). Requirement for internal insulation liner: - must not be toxic to the skin, releasing toxic fumes and odors -''s assessment must be accompanied by a sanitary certificate, or a certified copy of the qualified entity authorized skúšobnou.Pevnost strength must be at least 650 N / 5 cm (EN ISO 1421). Resistance to fungi and plesniam.Požiarna resistance - oxygen index min. 25, combustion gases are non-toxic and non-combustible part odkvápajúce (EN ISO 6940). Requirement for resistance to external influences: - Resistance to external temperatures from - 40C to + 55C without shape or design changes in external or internal parts - external resistance relative humidity up to 99% at 50 C, - resistance to wind speed of 100 km / h. (10 degree Beauffortovej scale), - resistance to precipitation as rain intensity of 3 mm / min, at an angle of 30 degrees in all directions - Resistance to precipitation in the form of snow with a limit of snow load between 10 kg / m² per 24 hodín.Požiadavka to the design of the tent: - color of the outer shell building in shade NATO khaki color-fast green (RAL 6031), - inflation valves supporting structure must be placed on the outside of the shell, - indoors shall be provided with no internal supports, including funding for Fixing lighting and spacing rods on the side of the structure - the structure must not significantly interfere in the internal space of the tent - external anchors from outside the tent must defend statutes linking with front and side stenami.Podlaha: - closely connected with the hall into a single unit, bearing capacity of the floor must meet the standards without special requirements for a minimum 5, 000 N / m² flat, 1, 000 N / m² points. Must be washable and dezinfikovatelná.Vyrovnávacie tiles under the tent: - protecting the tent floor from mechanical damage. Firming and countervailing terén.Okná: - minimum dimensions of 500 x 500 mm, mounted on the side walls at a minimum of 8 units on one strane.Prevedenie of transparencies, provided moskytierkou and allowing external covering material consistent with tarpaulin haly.Dvere: - initial door in the side wall depending on the design of minimum dimensions width 1300 mm, height 1800 mm.Minimálne 1 entry door in the side wall of minimum dimensions width 3100 mm, height 3200 mm.Požiadavky Technology Equipment: - Power Distribution 230 / 50 Hz for lighting and sockets, fuse, surge protection, protection against dangerous contact napätím.Osvetlenie and wiring - sub-distribution panel lights with wiring, brackets lamps, wiring from the outlet (at least 12 evenly spaced outlets on both sides), protected 32 A circuit protection IP 67.Podružný switchboards equipped with signal lights voltage in all phases of fusing pipe branch for zásuvky.Na seen spot located wiring zapojení.Vykurovanie: - oil, able to ensure the temperature inside the tent +20 C to +24 C in the amount of 1 meter above the ground when outside temperatures according to the point of use in climatic areas. Mains power supply: 230 V/50 Hz.Klimatizácia: - able to ensure the temperature inside the hall +20 C to +25 C at 1 m above the ground when outside temperatures according to point of use in climate oblastiach.Požiadavky maintenance: - insulating liner Laundry . Other parts of the buildings to be maintained by pressurized water. If necessary, the possibility of carrying out decontamination. Possibility of carrying out routine maintenance users by technological processes to be specified in the Operations dokumentácii.Požiadavky supplier of the package: - Multipurpose Halls and individual components delivered in protective packaging preventing mechanical and climatic damage, allowing decontamination. Palletised in a waterproof container that will extend over more than palety.Súcastou supply will: 1 circuit diagram of mobile electrification work including driveways marked places; 2 lighting mobile workplace min. 6 lights at 4 m s output min. 300 W (for each one); 3 cable crossovers with capacities up to 30 tons; 4 fire protection solution including frame extinguishers; 5 the design of the electrical systems including starting revision, fire policy, fire-alarm instructions, operating rules and still report to ballistic statutes (in terms of security structures and thus the protection of persons in tents) 6 backup power min. 3 kW for lighting the mobile site and the tent will offer dozorného.Súcastou: 1 submit outline proposals enlisted tents, halls and communication connection point to a power source; 2 staff training and service solutions for at least 5 years after completion dodávky.Verejný contracting authority will ensure the implementation of the shoulder measurement switchboards RE, PER type of circuit breaker before B63 / 3 distribution boards with IP 67 Description: Tents Authority Type: Body governed by public law Contact Nature: Supply contract Procedure: Not applicable Document: Prior Information Notice Regulation: European Union Award criteria: Not applicable CPV code: 39522530 CPV Description: Tents.   Internet address (URL): Directive: Classical Directive (2004/18/EC)
The bid deadline for Tents was 16 May 2015. Bidding is closed.
This tender has been issued by Centrum vycviku Lešt in Slovakia.
The tender value is not disclosed; please refer to the tender document. EMD / bid security details are provided in the tender document.
This tender is Self Financed
The tender is classified under the following CPV code(s): 39522530 - Tents.
The tender notice and related documents are listed in the Documents section above. Select a document to view or download it. Please log in or register to access the documents. If you cannot find additional documents in the Documents section, please log in to your account and Send Document Request from your account section.
The TendersOnTime reference is 838480. The purchaser document reference is 164212-2014.