Expired Tender India NCB TOT Ref. 151886520

Special reapir of BER Furniture for the QE Dec Tender - 151886520

Tender notice from India, published on 03 Nov 2026.

Executive Summary

The INDIAN ARMY has issued a Tender notice for the procurement of a Special reapir of BER Furniture for the QE Dec 2024 under, Qty: 707 in the India.The project location is South Andaman, Andaman and Nicobar Island (UT), India. This Tender notice was published on 03 Nov 2026 and is scheduled to close on 17 Nov 2026, with an estimated Tender value of 7481827. Interested bidders can access detailed Tender information, eligibility criteria, and complete bidding documents by referencing TOT Ref No. 151886520, while the tender notice number is GEM/2026/B/8018796 and Register on the platform.

Key facts

Summary
Special reapir of BER Furniture for the QE Dec 2024 under, Qty: 707
TOT Ref. No.
151886520
Document Ref. No.
GEM/2026/B/8018796
State
Andaman and Nicobar Island (UT)
Notice type
Tender
Competition
NCB
Publication date
03 Nov 2026
Bid deadline
17 Nov 2026
EMD
224000
Tender value
7481827
Purchaser ownership
Public
Procurement Type
Goods
Financier
Self Financed

CPV classification

Purchaser details

Purchaser contact is for registered users

Login to see details

Tender details

Almirah large steel with shelves, Almirah small steel with shelves, Chair Computer, Chair Visitor cushioned with Arms, Chair Easy with Cushion, Chair Revolving executive, Chair Plastic moulded with Arms and with Cushion, Chair dining JCOs oblique ORs, Chair writing., Charpoy IP with hard top, Chair 3 Seater with Arm and Back, Locker Bed Side Steel., Sofa set 4 Seater., Sofa set 5 Seater., Conference Table 14 Person, Table office Clk Steel., Table dining 6 pers., Table dining 4 pers., Peg table, Table Writing., Teapoy

Steel Almirah / Cabinets (V4)
BOQ Desc:

Almirah large steel with shelves. 1mm thick MS sheet shall be used to manufacture Almirah except legs. Two Legs shall be provided to almirah as shown on drawing and shall be of 1.25 mm thick MS sheet. Cromium plated stainless steel godrej type handle100mm long shall be fixed on shutters, Almirah shall be fitted with ISI marked 75mm 6 lever lock with three way locking system. Front shutters shall have two leaves of equal size. Almirah shall be finished with (shade of TA grey colour or as approved GE both internaly and externaly) two coats of synthetic enamel paint upto obtaining glossy finishing over a coat of redoxide primer with spray gun after properly smoothening the surface with sand paper. Rest all as specified/ shown in drawing and directed by Enginer-in-Charge.Drg No FD-1031

Almirah small steel with shelves. 1mm thick MS sheet shall be used to manufacture Almirah except legs. Two Legs shall be provided to almirah as shown on drawing and shall be of 1.25 mm thick MS sheet. Cromium plated stainless steel godrej type handle100mm long shall be fixed on shutters, Almirah shall be fitted with ISI marked 75mm 6 lever lock with three way locking system. Front shutters shall have two leaves of equal size. Almirah shall be finished with (shade of TA gray colour or as approved GE both internaly and externaly) two coats of synthetic enamel paint upto obtaining glossy finishing over a coat of redoxide primer with spray gun after properly smoothening the surface with sand paper. Rest all as specified/ shown in drawing and directed by Enginer-in-Charge. Drg No FD-1032

Chair Computer. As per trade pattern and directed by Enginer-in-Charge .Drg No TP

Chair Visitor cushioned with Arms. As per Trade patern and directed by Enginer-in-Charge.

Chair Easy with Cushion. All wood shall seasoned first class teak wood free from knots and defects hard nylon buffers shall be fixed at the bottom of legs with brass screws Seat & Back shall be made by 12mm thick BWR grade plywood over which 40 density foam 75mm thick shall be provided duly covered with best quality tapestry cloth as approved by GE. All exposed wooden surface shall be finished with french polish in light walnut shade or as approved by GE. Rest all as specified/ shown in drawing and directed by Enginer-in-Charge.Drg No FD-358

Chair Revolving executive As per trade pattern and directed by Enginer-in-Charge.

Chair Plastic moulded with Arms and with Cushion (Ornate). As per trade pattern and directed by Enginer-in-Charge.

Chair dining JCOs/ORs. All wood shall seasoned first class teak wood free from knots and defects.Hard Nylon buffers shall be fixed at the bottom of legs with brass screws. Readymade PVC seat 4 mm thick with holes shall be screwed with rails after providing one additional support of 25 x 25 mm Stiffner between and parallel to front and back rail, rest on side rail. All wooden surface shall be french polished with glossy finish, shade as approved by GE. Rest all as specified/ shown in drawing and directed by Engineer in Charge.Drg No FD/MAP-II/05

Chair writing. The frame of the chair shall be of 16 gauge 25mm dia MS tubular frame powder coated. Back shall be designed with contoured lumber support for extra comfort. 12mm thick hot pressed plywood upholstered with fabric and moulded polyurethane foam with PVC lippling alround shall be provided at seat and back. Arm rest shall be of black integral skin poly urethane with shore A hardness and reinforced with MS insert. It shall be scratch and wheather resistant. Both hand rest section shall have inner and outer dia of 210mm and 230mm respectively and have slope towards front. Rest all as specified / shown in drawing and directed by Engineer-in-Charge.Drg No FD/E6/MAP/12

Charpoy IP with hard top. Long and short rails of bed shall be 65 x 25 mm 16 gauge rectangle MS pipe.Stifners shall be 25 mm 16 gauge square MS pipe. Legs shall be 32 mm 16 gauge square MS pipe and welded properly at joints to make the charpoy. 25 x 60 x 6 mm cleats be welded with short rails inner side to support the plywood. 12 mm thick ply wood BWR type unpolished shall be provided to the top of charpoy screwed with cleat and stiffners by nut & washers. All steel members shall be finshed with two coats of synthetic enamel paint upto obtaining glossy finishing over a coat of redoxide primer with ...
Quantity Required: 707

Start Date: 02-11-2026 5:47 PM

End Date: 17-11-2026 1:00 PM

EMD Amount: 224000

BOQ Title: special reapir of BER Furniture for the QE Dec 2024 under

Relevant Categories: Steel Almirah / Cabinets (V4)

GeMARPTS Searched: Searched String: PEG TABLE FOOSBALL TABLE - SOCCER TABLE, Modular Table / Meeting Table / Centre Table (V2), Table - Tennis Table (V2), Computer Table (V3), Reception Table, Dressing Table, Executive Table (V4), Wilfley Table, Plastic Moulded Table - Preschool Kit, Composite Office Tables conforming...
Tender ID: GEM/2026/B/8018796

Documents

Tender Notice
Login to view
Bid_Document_9872368.pdf
Login to view
Specification_Document.pdf
Login to view
BOQ_Document.csv
Login to view

Bill of Quantities (BOQ)

# Title Description Qty Unit Delivery (Days)
1 Almirah large steel with shelves Almirah large steel with shelves. 1mm thick MS sheet shall be used to manufacture Almirah except legs. Two Legs shall be provided to almirah as shown on drawing and shall be of 1.25 mm thick MS sheet. Cromium plated stainless steel godrej type handle100mm long shall be fixed on shutters, Almirah shall be fitted with ISI marked 75mm 6 lever lock with three way locking system. Front shutters shall have two leaves of equal size. Almirah shall be finished with (shade of TA grey colour or as approved GE both internaly and externaly) two coats of synthetic enamel paint upto obtaining glossy finishing over a coat of redoxide primer with spray gun after properly smoothening the surface with sand paper. Rest all as specified/ shown in drawing and directed by Enginer-in-Charge.Drg No FD-1031 60 Nos 100
2 Almirah small steel with shelves Almirah small steel with shelves. 1mm thick MS sheet shall be used to manufacture Almirah except legs. Two Legs shall be provided to almirah as shown on drawing and shall be of 1.25 mm thick MS sheet. Cromium plated stainless steel godrej type handle100mm long shall be fixed on shutters, Almirah shall be fitted with ISI marked 75mm 6 lever lock with three way locking system. Front shutters shall have two leaves of equal size. Almirah shall be finished with (shade of TA gray colour or as approved GE both internaly and externaly) two coats of synthetic enamel paint upto obtaining glossy finishing over a coat of redoxide primer with spray gun after properly smoothening the surface with sand paper. Rest all as specified/ shown in drawing and directed by Enginer-in-Charge. Drg No FD-1032 55 Nos 100
3 Chair Computer Chair Computer. As per trade pattern and directed by Enginer-in-Charge .Drg No TP 10 Nos 100
4 Chair Visitor cushioned with Arms Chair Visitor cushioned with Arms. As per Trade patern and directed by Enginer-in-Charge. 4 Nos 100
5 Chair Easy with Cushion Chair Easy with Cushion. All wood shall seasoned first class teak wood free from knots and defects hard nylon buffers shall be fixed at the bottom of legs with brass screws Seat & Back shall be made by 12mm thick BWR grade plywood over which 40 density foam 75mm thick shall be provided duly covered with best quality tapestry cloth as approved by GE. All exposed wooden surface shall be finished with french polish in light walnut shade or as approved by GE. Rest all as specified/ shown in drawing and directed by Enginer-in-Charge.Drg No FD-358 23 Nos 100
6 Chair Revolving executive Chair Revolving executive As per trade pattern and directed by Enginer-in-Charge. 4 Nos 100
7 Chair Plastic moulded with Arms and with Cushion Chair Plastic moulded with Arms and with Cushion (Ornate). As per trade pattern and directed by Enginer-in-Charge. 10 Nos 100
8 Chair dining JCOs oblique ORs Chair dining JCOs/ORs. All wood shall seasoned first class teak wood free from knots and defects.Hard Nylon buffers shall be fixed at the bottom of legs with brass screws. Readymade PVC seat 4 mm thick with holes shall be screwed with rails after providing one additional support of 25 x 25 mm Stiffner between and parallel to front and back rail,rest on side rail. All wooden surface shall be french polished with glossy finish, shade as approved by GE. Rest all as specified/ shown in drawing and directed by Engineer in Charge.Drg No FD/MAP-II/05 27 Nos 100
9 Chair writing. Chair writing. The frame of the chair shall be of 16 gauge 25mm dia MS tubular frame powder coated. Back shall be designed with contoured lumber support for extra comfort. 12mm thick hot pressed plywood upholstered with fabric and moulded polyurethane foam with PVC lippling alround shall be provided at seat and back. Arm rest shall be of black integral skin poly urethane with shore A hardness and reinforced with MS insert. It shall be scratch and wheather resistant. Both hand rest section shall have inner and outer dia of 210mm and 230mm respectively and have slope towards front. Rest all as specified / shown in drawing and directed by Engineer-in-Charge.Drg No FD/E6/MAP/12 89 Nos 100
10 Charpoy IP with hard top Charpoy IP with hard top. Long and short rails of bed shall be 65 x 25 mm 16 gauge rectangle MS pipe.Stifners shall be 25 mm 16 gauge square MS pipe. Legs shall be 32 mm 16 gauge square MS pipe and welded properly at joints to make the charpoy. 25 x 60 x 6 mm cleats be welded with short rails inner side to support the plywood. 12 mm thick ply wood BWR type unpolished shall be provided to the top of charpoy screwed with cleat and stiffners by nut & washers. All steel members shall be finshed with two coats of synthetic enamel paint upto obtaining glossy finishing over a coat of redoxide primer with spray gun after properly smoothening the surface with sand paper in black colour. Rest all as specified/ shown in drawing and directed by Enginer-in-Charge.Drg No FD/MAP-II/01 95 Nos 100
11 Chair 3 Seater with Arm and Back Chair 3 Seater with Arm and Back. As per trade pattern and directed by Engineer in Charge 10 Nos 100
12 Locker Bed Side Steel. Locker Bed Side Steel. 1mm thick MS sheet shall be used to manufacture locker except legs. Two Legs shall be provided to almirah as shown on drawing and shall be of 1.25 mm thick MS sheet. Cromium plated stainless steel godrej type handle100mm long shall be fixed on shutters, Locker shall be fitted with ISI marked 75mm 6 lever lock with three way locking system (Make of lock -Harrison/Link/Godrej). Front shutters shall have two leaves of equal size. Locker shall be finished with (shade of TA gray colour or as approved GE both internaly and externaly) two coats of synthetic enamel paint upto obtaining glossy finishing over a coat of redoxide primer with spray gun after properly smoothening the surface with sand paper. Rest all as specified/ shown in drawing and directed by Enginer-in-Charge.Drg No FD-1029 70 Nos 100
13 Sofa set 4 Seater. Sofa set 4 Seater. The set consist of one long piece of two seater and two small pieces of single seater. All timber work shall be first class seasoned teak wood free from knots/defects. Cushion for seat and back shall be of 100mm thick 40 density duly covered with fabric/tapestry cloth composition of 65% polyester & 35% cotton or as approved by GE and make of cushion shall be kurlon/sleepwell. All the wooden joints shall be fixed with bamboo pins and nails shall not be used. All exposed wooden surface shall be finished with Deco polish in light walnut shade or as approved by GE. Rest all as specified/ shown in drawing and directed by Engineer-in-Charge.Drg No FD-281 16 Set 100
14 Sofa set 5 Seater. Sofa set 5 Seater. The set consist of one long piece of three seater and two small pieces of single seater. As per trade pattern. 1 Set 100
15 Conference Table 14 Person Conference Table 14 Person. As per trade pattern Eco moudler of Godrej.Drg No TP 2 Nos 100
16 Table office Clk Steel. Table office Clk Steel. Top shall be 18 mm thick exterior grade pre laminated MDF board one side laminated in light Wallnut shade or as approved by BSO/GE, duly covered with 4 mm thick half round teak wood beading in matching shade with synthetic adhesive(Fevicol SH). with two coats of synthetic enamel paint upto obtaining glossy finishing over a coat of redoxide primer with spray gun after properly smoothening the surface with sand paper in black colour. Rest all as specified/ shown in drawing and directed by Enginer-in-Charge.Drg No FD-1004 25 Nos 100
17 Table dining 6 pers. Table dining 6 pers. All wooden part shall be first class seasoned teak wood free from knots and defects. Hard rubber/nylon buffers shall be fixed at the bottom of legs with brass screws, Top shall be 18mm thick exterior grade MDF board one side laminated shade as approved by GE, duly fixed with 4mm thick teak wood beading in matching shade with synthetic adhesive (Fevicol SH) 8 Nos of L-shape corner of flat iron 5mm thick 4 x 4 inch between legs and rail to be fixed with screw. All wooden surface shall be french polished with glossy finish shade as approved by GE Rest. all as specified/ Shown in drawing and directed by Enginer-in-Charge. Drg No FD/MAP-II/03 20 Nos 100
18 Table dining 4 pers. Table dining 4 pers. All wooden part shall be first class seasoned teak wood free from knots and defects. Hard rubber/nylon buffers shall be fixed at the bottom of legs with brass screws, Top shall be 18mm thick exterior grade MDF board one side laminated shade as approved by GE, duly fixed with 4mm thick teak wood beading in matching shade with synthetic adhesive (Fevicol SH) 8 Nos of L-shape corner of flat iron 5mm thick 4 x 4 inch between legs and rail to be fixed with screw. All wooden surface shall be french polished with glossy finish shade as approved by GE Rest. all as specified/ Shown in drawing and directed by Enginer-in-Charge.Drg No FD/MAP-II/03 33 Nos 100
19 Peg table Peg table. All wood shall seasoned first class teak wood free from knots and defects. Hard Nylon buffers shall be fixed at the bottom of legs with brass screws. H Type leg stiffeners shall be provided for better support. Top shall be 18 mm thick exterior grade MDF board one side laminated in light Wallnut shade or as approved by GE, duly covered with 4 mm thick teak wood beading in matching shade with synthetic adhesive(Fevicol SH). All wood surfaces shall be french polished with high glossy finish. Rest all as specified/ shown in drawing and directed by Enginer-in-Charge.Drg No FD-384 68 Nos 100
20 Table Writing. Table Writing. All wood shall be of seasoned 1st class hardwood teakwood. Legs shall be of 35mmx55mm in section and 717mm high having 5mmx5mm in section groove at the top of legs at the portion when placed in position. Top of tables shall be of 18mm thick pre-laminated MDF board with 4mm teak wood edging all round the top of table. Two short stiffeners of teakwood of size 50mmx40mm in section irrespective of what is shown on drg shall be provided between legs at 100mm from bottom of legs. Sides of the box which house the drawers and cabinet shall be 18mm thick pre-laminated particle board exterior grade. Sides and back of drawers shall be of 12mm thick teak wood planks. Bottom of drawers shall be of 6mm thick plywood commercial 6mm thick plywood commercial 75mm high partition shall be provided in the drawer. Shutter for cabinet shall be fixed with piano type continuous hinges. Lock shall be provided to drawer and shutters. Recessed handle shall be provided to drawer and shutter 25mm dia and 25mm high rubber shoes shall be fixed to bottom of legs. Rest. all as specified/ Shown in drawing and directed by Enginer-in-Charge.Drg No FD-275 28 Nos 100
21 Teapoy Teapoy. The leg shall be 60mm x 30mm in section and 497 mm high and shall be of teak wood 5mm x 5mm in section groove shall be provided at the visible portion of the top of legs. Top rail of teak wood of 20mm x 50mm in section and 510mm long shall be provided between the legs bottom rail of teak wood of 20mm x 50mm in section and 420mm long shall be provided between legs, widthwise at 100mm above the bottom of legs. A centre rail of size 20mm x 50mm shal also be provided lengthwise at centre in between the side bottom rails irrespective of what is shown on drg 25mm thick and 25mm dia hard rubber PVC rings shall be fixed to the bottom of all legs fixed with 30 mm long screws. Top of the table shall be of 18mm thick pre laminated MDF boar exterior grade of approved shade with 4mm thick teak wood beading all round the edges of top. Rest all as specified/ shown in drawing and directed by Engineer-in-Charge.Drg No FD-382 57 Nos 100

Similar tenders

India Public Procurement Intelligence

Frequently asked questions

The bid deadline for Special reapir of BER Furniture for the QE Dec 2024 under, Qty: 707 was 17 Nov 2026. Bidding is closed.

This tender has been issued by INDIAN ARMY in India.

The estimated tender value is ₹7481827. The EMD / bid security is ₹224000.

This tender is Self Financed

This is a Goods procurement tender issued as a public sector opportunity in India.

The tender is classified under the following CPV code(s): 39151200 - Work benches, 19245000 - Lining fabrics, 39135000 - Sorting tables.

The tender notice and related documents are listed in the Documents section above. Select a document to view or download it. Please log in or register to access the documents. If you cannot find additional documents in the Documents section, please log in to your account and Send Document Request from your account section.

The TendersOnTime reference is 151886520. The purchaser document reference is GEM/2026/B/8018796.

See the Similar Tenders section on this page or browse other tenders from India.

This tender falls under Technology and Equipment, Materials and Products in India. Suppliers in these sectors can track similar India tenders using CPV-based alerts.