Supply & Commissioning of Vehicles Tender, Mauritius - 65258844

Procurement Summary

Country : Mauritius

Summary : Supply & Commissioning of Vehicles

Deadline : 09 May 2022

Other Information

Notice Type : Tender

TOT Ref.No.: 65258844

Document Ref. No. : MCCPL/IFB/2022/133

Financier : Self Financed

Purchaser Ownership : Public

Tender Value : Refer Document

Purchaser's Detail

Name :Login to see tender_details

Address : Login to see tender_details

Email : Login to see tender_details

Login to see details

Tender Details

Tenders are invited for Supply & Commissioning of Vehicles

1 Dump Truck(Fully Factory built) 2 Unit Mechanical Workshop, Abbattoir Road, Roche Bois 4 months 5 months 2 Low bed towing truck with locally manufactured Rear Ramps 1 Unit 3 months 4 months 3 Skid steer loaders on pneumatic tyres complete with attachment 2 Unit 3 months 4 months 4 Pickup Van-Double Cab with rear cargo bed 2 Unit 2 months 3 months 5 Universal Tyre changer 1 Unit 2 months 3 months

Make
Bidder to Specify
Model
Bidder to Specify
Country of Origin
Bidder to Specify
Engine Diesel and Water- Cooled
Engine Capacity 4200-4600cc Naturally Aspirated
Payload- 3000 - 4000 Kg (Calculation to be Given)

Steering Right Hand Drive, Power Assisted and Preferably Adjustable
Transmission Manual with Five or More Forward, Reverse
Chassis Chassis shall be Suitable for Dump Application.
Gross Vehicle Weight 7000-8000 Kg
Dimensions Overall Length: 5000 - 5500 Mm
Overall Width: 2000 - 2200 Mm
Short Wheelbase 2500 - 2800 Mm
Speed Limiter to be Fitted as Per Ntla Regulations and Comply with Bs Au 217 or Approved Equivalent
Power Take off Factory Fitted to Meet Requirements of the Tipper Mechanism and Payload and to be Actuated from Cabin.
Tipper Mechanism • Scissor Type Tipper Mechanism with Tipping Angle of 50 to 60 Degrees and Capacity not Less than Payload including Weight of Dump Body.
• to Specify Make, Model, Capacity and Provide Leaflet Clearly Indicating the Model Proposed.
• Factory Design, Factory Built and Factory Fitted Complete with Sub-Frame Assembly, Power Take off Control and Dump Lever
• to be Equipped with All Required Locks and Devices for Safe Operation.
Brake • Hydraulic Dual Circuit
• Auxiliary Exhaust Brake
• Parking Brake Mechanical Type

Cabin (I) Seating Capacity for Driver + 2, All with Seat Belts
(Ii) Original Interior and Exterior Rear View Mirrors
(Iii) am/Fm Radio, Heater/Defroster
(Iv) Heavy Duty Rubber Mats to Cover Completely the Cabin Floor
(v) Tilt Type Preferably
(Vi) Instruction Panel with All Warning Indications
(Vii) Air Conditioner
Rear Lights Suitably Located, Mounted and Protected with Galvanized Grilles
Accessories I) Spare Wheel Suitably Located and Secured on Wheel Carrier for Easy Access and Manipulation.
Ii) Appropriate Hydraulic Jack of about 4t Capacity, Complete with Lever and Wheel Spanner
Iii) Warning Triangular Reflectors, Yellow Chalk and Standard Forms.
Iv) 2kg Dry Powder Fire Extinguisher Suitably Mounted within Driver-S Reach as Per Ntla Regulations
V) Revolving Beacon Lamp or Led Flashing Light on Cab with Covered Galvanized Grilles
Vi) Rear Warning Sign + Fluorescent Reflective Band as Per Ntla Regulations.
Vii) Two Fog Led Lamps at Rear with Galvanized Grilles
Viii) One Set of Standard Tools Complete with Tool Box
Ix) First Aid Box for Seven Persons Appropriately Fixed in Cabin.
x) Lockable Fuel Tank Cap and Hydraulic Oil Tank Cap Where Applicable.
xi) Warning Buzzer for Reverse Gear
(xii) Other Standard Accessories to be Supplied. Bidder to Mention.
Guards • Front Heavy Duty Original Mud Guards with Mud Flaps as Per Ntla Regulations
• Rear Heavy Duty Galvanized Mud Guards with Mud Flaps as Per Ntla Regulations. Rear under Run Protection and Side Guards as Per Ntla Regulations.
Dump Body • Heavy Duty Dump Body to be Factory Built and Factory Fitted
• Tipper Mechanism Sub Frame to be at Least 75 Mm Height
• Dump Body Mainframe to be at Least 75 Mm Height
• Length of Body to be about 3000 Mm
• Height of Dump Body Side Panels shall be Minimum of 300 Mm and at Least 2 Mm Thickness
• Flooring to be of Minimum 3mm Thickness
Tail Gate: To be Hinge from the Top and Heavy Duty Locking Device below
Tarpaulin Cover with Metal Eyelets of Appropriate Dimension Complete with Nylon Rope to be Provided to Cover Whole Rear Body and Galvanized Hooks to be Fixed on Both Sides Panels
Drawings Bidder to Submit Detailed Drawings of Propose Truck and Tipper Mechanisms with Dump Body.
Painting Appropriate Etch Primer for Galvanized Material and Undercoat to be Applied Prior to Finish Colour.
• Cabin -White
• Chassis- Black

Documents

 Tender Notice